
PA300 Tension Clamp for Round Cables
The PA300 tension clamp for round conductors anchors LV-ABC lines with insulated neutral messengers, rated 2.5 kN breaking load. Conductor range confirmed against the drawing.
- Model: PA300
- Breaking Load: 2.5kN
Product Description
The PA300 is a tension clamp for round conductors, used to anchor and tighten LV-ABC lines with an insulated neutral messenger. The conductors are gripped along the clamp body so the mechanical tension of the span transfers into the clamp rather than into the insulation.
The body grips the cable jacket without crushing it, and the clamp is installed by hand — no special tooling is required on site.
Rated 2.5kN breaking load.
Technical Specifications
| Item | Specification |
| Model | PA300 |
| Product Type | Tension Clamp for Round Cables |
| Breaking Load | 2.5kN |
| Product Category | Aerial Cable Accessories |
| Manufacturer | GGLDF |
Conductor range is not published for this model. Send us the core count and conductor cross-section and we will confirm the specification against the drawing before you order.
How to Select the Right Model
Two things decide which model fits: the number of conductors and their cross-section. The range is written as core count × conductor range — for example 4×16-25mm² means four conductors of 16 to 25 mm² each.
| Model | Conductor range | Breaking load | Core |
| PA2/25 | 2×10-35mm² | 2.5kN | 2-core |
| PA2/35 | 2×16-35mm² | 5kN | 2-core |
| PA4/35 | 2×16-35mm² | 5kN | 2-core |
| GD160 | 2×16-35mm² | 5kN | 2-core |
| PA4/16~35 | 4×16-35mm² | 12kN | 4-core |
| RPA425/70 | 4×16-50mm² | 20kN | 4-core |
| GD161 | 4×16-35mm² | 5kN | 4-core |
| NES-1S | 4×16-50mm² | 20kN | 4-core |
| PA4/25 | 4×16-25mm² | 2.5kN | 4-core |
| PA-25S | 4×16-25mm² | 2.5kN | 4-core |
| NES-2S | 4×50-120mm² | 20kN | 4-core |
| PA300 | confirm against drawing | 2.5kN | single / mixed |
| PA16~95 | 4-120mm² | 2.5kN | single / mixed |
| PA16 | 10-70 mm² | 3kN | single / mixed |
| JBG-50-1000 | 25-50mm² | 10kN | single / mixed |
| PA-903 | 25-70/2×10-25mm² | 1.5kN | single / mixed |
| PA1500 | 50-70mm² | 6kN | single / mixed |
| PA2000 | 70-95mm² | 6kN | single / mixed |
Match both the core count and the section, then check that the breaking load is adequate for the span. If your conductors fall outside every row, send us the core count and cross-section and we will confirm the model rather than guess.
Key Advantages
- Grips the conductor jacket without crushing the insulation
- Distributes tension along the conductors instead of concentrating it at one point
- Rated 2.5kN breaking load
- Fitted without special tooling
Typical Applications
- Dead-end and anchor termination of LV-ABC lines with insulated neutral messengers.
- Strain locations where the full conductor tension must be absorbed.
- Span termination on distribution poles and brackets.
- Outdoor installations exposed to weather.
Send us the core count, conductor cross-section, quantity and destination port for a quotation with pricing and lead time. View all tension clamp models →
